+90(312)309 20 86
info@mteturkey.com
HYDROCAL 1001+
Cost effective and comprehensive monitoring of 6 fault gases
· Measurement of Moisture (H2O) in the transformer oil
· Easy and fast installation while the transformer is operating · Compact and resistant design for long lasting usage
· ETHERNET and CAN bus interfaces to support proprietary communication protocols and to be open / prepared for substation communication protocols MODBUS®TCP, CANopen
The Hydrocal 1001+ is a permanently installed composite gas in oil sensor for the Total Dissolved Combustible Gases (TDCG) analysis of the key fault gases Hydrogen (H2), Carbon Monoxide (CO), Methane (CH4), Acetylene (C2H2), Ethylene (C2H4) and Ethane (C2H6).
To detect an even wider range of potential transformer faults, the Hydrocal 1001+ analyses additionally the content of Moisture (H2O) in the transformer oil.
The Hydrocal 1001+ is a fully integrated (6 key fault gases and Moisture in oil) compact and cost effective device used in particular for early transformer fault detection and preventative maintenance.
Click for the Leaflet
HYDROCAL 1003
Maintenance free system
· Easy to mount on the operating transformer without any operational interruption
· ETHERNET (Option), RS 232 and RS 485 interfaces to support MODBUS® RTU/ASCII, DNP3 and proprietary communication protocols and to be open / prepared for substation communication protocol IEC 61850
· Option: Offshore version The Hydrocal 1003 is an online transformer monitoring device for the dissolved gas analysis (DGA) of the key fault gases Hydrogen (H2) and Carbon Monoxide (CO).
In addition, water contamination deteriorates the performance of the oil as high moisture content increases the risk of corrosion and overheating.
The Hydrocal 1003 reacts on this issue and provides its users the analysis of Moisture (H2O) in the transformer oil to achieve an even higher safety standard
Click for the Leaflet
HYDROCAL 1003 OFFSHORE
Individual analysis of the dissolved gas contents hydrogen (H2) and carbon monoxide (CO)
Analysis of moisture (H2O) dissolved in transformer oil (both, relative humidity [%] and absolute humidity [ppm])
Special design for Offshore Wind Power Applications:
Housing without window painted C5M
Back plate with 2 cable glands M20 (chrome-nickel steel, IP 55, corrosion-free and acid-resistant). Optional with 4 cable glands (2x M20 and 2 x M25).
Back plate, oil entrance and housing screws made of stain-less steel V4A
Easy to mount on a transformer valve (G 1½" DIN ISO 228-1 or 1½" NPT ANSI B 1.20.1)
Installation on the operational transformer without any opera-tional interruption
Advanced software (on the unit and via PC)
Maintenance free system
Communication interfaces ETHERNET (Option) 10/100 Mbit/s (copper-wired / RJ45 or fibre-optical / SC duplex), RS 232 and RS 485 to support MODBUS® RTU/ASCII, DNP3 and proprie-tary communication protocols and to be open / prepared for substation communication protocol IEC 61850
Optional GSM- or analog modem for remote access
Optional DNP3 serial modem for SCADA connection
Click for the Leaflet
HYDROCAL 1004 genX
Individual measurement of Hydrogen (H2), Carbon Monoxide
(CO) and Acetylene (C2H2)
Moisture in Oil (H2O) measurement
Easy to mount on a transformer valve
(G 1½" DIN ISO 228-1 or 1½" NPT ANSI B 1.20.1)
Easy to mount on the operating transformer without any operational interruption
Maintenance free system due to less movable parts
Advanced software (on the unit and via PC) with intuitive operation by 7” color TFT capacitive touchscreen, WLAN and Webserver
operation from any smart phone, tablet or notebook
Communication interfaces ETHERNET 10/100 Mbit/s (copperwired
/ RJ 45 or fibre-optical / SC Duplex) and RS 485 to
support MODBUS® RTU/ASCII, MODBUS
TCP, DNP3,proprietary communication protocols and substation communication protocol IEC 61850
Optional external I/O module
Click for the Leaflet
HYDROCAL 1005
Maintenance free system
Easy to mount on the operating transformer without any operational interruption ·
ETHERNET and RS 485 interfaces to support MODBUS®RTU/ ASCII, MODBUS®TCP, DNP3 and proprietary communication protocols and to be open / prepared for substation communication protocol IEC 61850 ·
Option:
Offshore version The Hydrocal 1005 is a permanently installed multi gas in oil analysis system with transformer monitoring functions.
It individually measures Moisture in oil (H2O) and the key gases Hydrogen (H2), Carbon Monoxide (CO), Acetylene (C2H2) and Ethylene (C2H4) dissolved in the transformer oil.
Especially the presence and increase of Acetylene (C2H2) and Ethylene (C2H4) further classifies the nature of a fault as overheating, partial discharge or high energy arcing.
The Hydrocal 1005 offers as a compact transformer monitoring system by the integration of other sensors present on a transformer (TCU Transformer Control Unit and / or bushing monitoring).
Click for the Leaflet
HYDROCAL 1005 -3/-2/-1
· Cost efficient monitoring of up to three transformer tanks with one Hydrocal 1005-3/-2/-1 ·
ETHERNET and RS 485 interfaces to support MODBUS®TCP, DNP3 and proprietary communication protocols and to be open / prepared for substation communication protocol IEC 61850
The Hydrocal 1005-3/-2/-1 is a multi gas in oil analysis system for the monitoring of a bank of up to three single phase transformers located close to each other.
The wall mounted system individually measures Moisture in oil (H2O) and the key gases Hydrogen (H2), Carbon Monoxide (CO), Acetylene (C2H2) and Ethylene (C2H4) dissolved in the transformer oil utilising a smart sampling system that samples oil from each tank via three separate oil channels.
It furthermore serves as a compact transformer monitoring system by the integration of other sensors present on a transformer.
Click for the Leaflet
HYDROCAL 1005 OFFSHORE
Individual measurement of Hydrogen (H2), Carbon Monoxide (CO), Acetylene (C2H2) and Ethylene (C2H4)
Moisture in oil (H2O) measurement
Special design for offshore applications:
Housing without window painted in C5M
Back plate with cable glands (chrome-nickel steel, IP 68, corrosion-free and acid-resistant)
Back plate, oil entrance and housing screws made of stain-less steel V4A
Easy to mount on a transformer valve (G 1½" DIN ISO 228-1 or 1½" NPT ANSI B 1.20.1)
Installation on the operational transformer without any operational interruption
Advanced software (on the unit and via PC)
Maintenance free system
Communication interfaces ETHERNET 10/100 Mbit/s (copper-wired /RJ 45 or fibre-optical / SC Duplex) and RS 485 to support MODBUS®RTU/ASCII, MODBUSTCP, DNP3 proprietary communication and IEC 61850 protocols
Optional on-board GSM or analog modem for remote access
Optional DNP3 serial modem for SCADA connection
Optional IEC 61850 modem for SCADA connection
Click for the Leaflet
HYDROCAL 1006 genX
Individual measurement of Hydrogen (H2), Carbon Monoxide
(CO), Acetylene (C2H2), Methane (CH4) and Ethylene (C2H4)
Moisture in Oil (H2O) measurement
Easy to mount on a transformer valve
(G 1½" DIN ISO 228-1 or 1½" NPT ANSI B 1.20.1)
Easy to mount on the operating transformer without any operational interruption
Maintenance free system due to less movable parts
Advanced software (on the unit and via PC) with intuitive operation
by 7” color TFT capacitive touchscreen, WLAN and Webserver
operation from any smart phone, tablet or notebook PC
Communication interfaces ETHERNET 10/100 Mbit/s (copperwired
/ RJ 45 or fibre-optical / SC Duplex) and RS 485 to support
MODBUS® RTU/ASCII, MODBUSTCP, DNP3, proprietary
communication protocols and substation communication protocol IEC 61850
Optional external I/O module
Click for the Leaflet
HYDROCAL 1008
Product Information
Maintenance free system ·
Easy to mount on the operating transformer without any operational interruption ·
ETHERNET and RS 485 interfaces to support MODBUS®RTU/ASCII, MODBUS®TCP, DNP3 and proprietary communication protocols and to be open / prepared for substation communication protocol IEC 61850 ·
Option: Offshore version The Hydrocal 1008 is a permanently installed multi-gas-in-oil analysis system with transformer monitoring functions.
It individually measures Moisture in oil (H2O) and the key gases Hydrogen (H2), Carbon Monoxide (CO), Carbon Dioxide (CO) Methane (CH4), Acetylene (C2H2), Ethylene (C2H4) and Ethane (C2H6) dissolved in the transformer oil.
With the accurate analysis of 7 fault gases plus Moisture in oil, the Hydrocal 1008 is MTE ́s most comprehensive transformer monitoring system,
which can be even expanded with different extension packages TCU Transformer Control Unit and / or Bushing Monitoring.
Click for the Leaflet
HYDROCAL 1008 OFFSHORE
Individual measurement of Hydrogen (H2), Carbon Monoxide
(CO), Carbon Dioxide (CO2), Methane (CH4), Acetylene (C2H2),
Ethylene (C2H4) and Ethane (C2H6)
Moisture in oil (H2O) measurement
Special design for offshore applications:
Housing without window painted in C5M
Back plate with cable glands (chrome-nickel steel, IP 68,corrosion-free and acid-resistant)
Back plate, oil entrance and housing screws made of stainless steel V4A
Easy to mount on a transformer valve
(G 1½" DIN ISO 228-1 or 1½" NPT ANSI B 1.20.1)
Installation on the operational transformer without any operational interruption
Advanced software (on the unit and via PC)
Maintenance free system
Communication interfaces ETHERNET 10/100 Mbit/s (copperwired
/ RJ 45 or fibre-optical / SC Duplex) and RS 485 to support
MODBUS®RTU/ASCII, MODBUSTCP, DNP3 proprietary
communication and IEC 61850 protocols
• Optional on-board GSM or analog modem for remote access
• Optional DNP3 serial modem for SCADA connection
• Optional IEC 61850 modem for SCADA connection
• Optional HV and LV bushing sensors for HV and LV bushing
monitoring applications via communication interface
Click for the Leaflet
HYDROCAL 1009
Product Information
Multi-Gas-in-Oil Analysis System with Transformer Monitoring Functions.
The Hydrocal 1009 is a permanently installed multi-gas-in-oil analysis system with transformer monitoring functions.It individually measures, Moisture in Oil (H2O) and the key gases Hydrogen (H2),Carbon Monoxide (CO),Carbon Dioxide (CO2),Methane (CH4),Acetylene (C2H2),Ethylene (C2H4),Ethane (C2H6) and Oxygen (O2) dissolved in transformer oil.
Key Advantages
Individual measurement of Hydrogen (H2), Carbon Monoxide (CO),Carbon Dioxide (CO2),Methane (CH4),Acetylene (C2H2),Ethylene (C2H4),Ethane (C2H6) and Oxygen (O2)
Moisture in Oil (H2O) measurement
Easy to mount on a transformer valve
Installation on the operational transformer without any operational interruption
Advanced software (on the unit and via PC)
Maintenance free system
Communication interfaces ETHERNET 10/100 Mbit/s (copper-wired /RJ 45 or fibre-optical /SC Duplex) and RS 485 to support MODBUS ® RTU/ASCII, MODBUS®TCP,DNP3 proprietary communication and IEC 61850 protocols
Optional on-board GSM or analog modem for remote access
Optional DNP3 serial modem for SCADA connection
Optional IEC 61850 modem for SCADA connection
Optional HV and LV bushing sensors for HV and LV bushing monitoring applications via communication interface
Click for the Leaflet
HYDROCAL 1009 OFFSHORE
Individual measurement of Hydrogen (H2), Carbon Monoxide
(CO), Carbon Dioxide (CO2), Methane (CH4), Acetylene (C2H2),
Ethylene (C2H4), Ethane (C2H6) and Oxygen (O2)
Moisture in Oil (H2O) measurement
Special design for offshore applications:
Housing without window painted in C5M
Back plate with cable glands (chrome-nickel steel, IP 68,
corrosion-free and acid-resistant)
Back plate, oil entrance and housing screws made of stainless
steel V4A
Easy to mount on a transformer valve (G 1½" DIN ISO 228-1 or 1½" NPT ANSI B 1.20.1)
Installation on the operational transformer without any operational interruption
Advanced software (on the unit and via PC)
Maintenance free system
Communication interfaces ETHERNET 10/100 Mbit/s (copperwired
/ RJ 45 or fibre-optical / SC Duplex) and RS 485 to support
MODBUS®RTU/ASCII, MODBUS
TCP, DNP3 proprietary communication and IEC 61850 protocols
Optional on-board GSM or analog modem for remote access
Optional DNP3 serial modem for SCADA connection
Optional IEC 61850 modem for SCADA connection
Optional HV and LV bushing sensors for HV and LV bushing monitoring applications via communication interface
Click for the Leaflet
